SUPERMARINE SPITFIRE MKIX 67" 3D Printed RC 3dLabPrint Model Airplane Kit

Description

I will print in Silver, any and all questions are welcome.  I can print any plane from 3DLabPrint
I need 3-6 days to print and ship out, if not in stock
These models come with a PDF file for decals
General specifications:
Length: 1488 mm / 58,6 inch
Wingspan: 1700mm / 66.9 inch
Wingspan (clipped wing): 1505mm / 59.3 inch
Height: 510 mm / 20.1 inch
Wing area: 51.4 dm2 / 5.53 sq ft
Wing loading: 71.9 g/dm2 / 23.6 oz at sq ft
Center of gravity: 102mm / 4.01 in from LE
See CG tags on wings...
Airfoil: 3DLabPrint SPT02
Weight of all printed parts: 2060 g / 72.7 oz
Takeoff weight (6s 4500mAh Li-Pol): 3700 g / 130.5 oz
Max takeoff weight: 4200 g / 148.2 oz
Never exceed speed, VNE: 160 km/h / 99.4 mph
Design maneuvering speed, VA: 120 km/h / 74.6 mph
Stall speed, VS(full flaps): 38 km/h / 23.6 mph
Performance measurement:
Max speed VH (level flight): 140 km/h – 75.6kn – 87.0mph
Rate of climb: 28 m/s (5 500 ft/min)
Flight time (6s 4500mAh): 10:00 min (+30% reserve)
Includes:
all 3Dprinted parts for model
Printed user guide
You’ll need to provide:
CA Glue - medium or similar medium viscosity CA glue
Activator for CA Glue or similar, but gas presurized aerosol is better
Snap knife
4x nylon washers with aprox 4mm inner hole
4x steel washers with 4mm inner hole (for front montage only)
4x 4/12mm screew (for front montage only)
4-6x 4/30mm self tapping screw
CA Glue - medium or similar medium viscosity CA glue
Activator for CA Glue or similar, but gas presurized aerosol is better
1x ballpoint pen spring (a spring from old ballpoint pen will work fine)
Snap knife
Soldering Iron or any hot tool
CA Glue - medium viscosity CA glue
Activator for CA Glue or similar, but gas presurized aerosol is better
1.2 mm /16AWG steel pushrod wires
Wire cutter, Z bend pliers or pliers.
Snap knife
6x Hitec HS-82 or similar, size: 30 x 30 x 12mm servos
servo extension cables 300mm / 12 inch
1.5 mm /14AWG pushrod wires for ailerons
1.2 mm /16AWG pushrod wires for flaps
Wire cutter, Z bend pliers or pliers.
option 1:
2x Turnigy 90 Degree All Metal Servoless Retract Unit 90 Size
1x Turnigy 60~90 size Alloy Sprung Oleo Strut with Trailing Link (110mm)
or option 2:
1x Servoless Retract with Metal Trunion 44mm x 41mm Mount
1x Alloy Oleo Strut 115mm Straight Mains for 40~60 Class
8x 4/30mm self tapping screw
2x ballpoint pen spring (a spring from old ballpoint pen will work fine)
or any thin rope or wire
Some tested setups:
SETUP A)
Motor: AXI 4120/20 GOLD LINE V2 465KV
ESC: MEZON 120 lite or similar at leats 70A/6s
Battery: ZIPPY Compact 4500mAh 6S 35C or similar 6s weight approx 700g
Propeller: Turnigy Type A Beech Wood 3-Blade Propeller 15x8
alternatively Turnigy Beech Wood Propeller 15x8
SETUP B)
Motor: Turnigy Aerodrive SK3 - 5055-430KV or similar with same KV and weight
ESC: HobbyKing 70A BlueSeries or similar at leats 70A/6s
Battery: ZIPPY Compact 4500mAh 6S 35C or similar 6s weight approx 700g
Propeller: Turnigy Type A Beech Wood 3-Blade Propeller 15x8
alternatively Turnigy Beech Wood Propeller 15x8
SETUP C)
Motor: LEOPARD LC5065-7T 380KV or similar with same KV and weight
ESC: HobbyKing 70A BlueSeries or similar at leats 70A/6s
Battery: ZIPPY Compact 4500mAh 6S 35C or similar 6s weight approx 700g
Propeller: APC 15.5x12-4 Blade Propeller
your own Rx/Tx system, 9channel (at least 6ch)
nylon nuts and screws or any 5-6/60mm
adhesive velcro strip for Li-Pol battery, ESC and Receiver
battery strap
some gauge (f.e. ruler)
More details for the model can be found at 3d LabPrint's website: www.3dlabprint
Returns:
If you're not happy with the model I will accept returns as long as it's complete, and totally unassembled. If there's damage during shipping I will send you the parts you need free of charge. Also if you have a hard landing and need replacement parts, just contact me and i can get you a quote for the parts you may need.